Search Results

This research focused on the effects of split injection on combustion in a diesel environment. It was done in a specially designed engine-fed combustion chamber (swirl ratio of 5) with full field optical access through a quartz window. The simulated engine combustion chamber used a special backwards spraying injector (105°). The electronically controlled injector could control the size and position of it's, two injections. Both injections were through the same nozzle and it produced very rapid injections (1.5 ms) with a maximum injection pressure of 130 MPa. Experimental data included: rate of injection, injector pressure, combustion chamber dumping (NO & NOx concentrations), flame temperature, KL factor (soot concentration) combustion pressure, and rate of pressure rise. Injection rates indicate that the UCORS injection system creates very rapid injections with the ability to produce controllable split injections.

Experiments were performed on a homogeneously fueled compression ignition gasoline-type engine with a high degree of intake charge preheating. It was observed that fuels that contained lower end and/or non-branched hydrocarbons (gasoline and an 87 octane primary reference fuel (PRF) blend) exhibited sensitivity to thermal conditions in the surge tanks upstream of the intake valves. The window of intake charge temperatures, measured near the intake valve, that provided acceptable combustion was shifted to lower values when the upstream surge tank gas temperatures were elevated. The same behavior, however, was not observed while using isooctane as a fuel. Gas chromatograph mass spectrometer analysis of the intake charge revealed that oxygenated species were present with PRF 87, and the abundance of the oxygenated species appeared to increase with increasing surge tank gas temperatures. No significant oxygenated species were detected when running with isooctane.

A study was performed in which the effects on the regulated emissions from a commercial small DI diesel engine were measured for different refinery-derived fuel blends. Seven different fuel blends were tested, of which two were deemed to merit more detailed evaluation. To investigate the effects of fuel properties on the combustion processes with these fuel blends, two-color pyrometry was used via optically accessible cylinderheads. Additional data were obtained with one of the fuel blends with a heavy-duty DI diesel engine. California diesel fuel was used as a baseline. The fuel blends were made by mixing the components typically found in gasoline, such as methyl tertiary-butyl ether (MTBE) and whole fluid catalytic cracking gasoline (WH-FCC). The mixing was performed on a volume basis. Cetane improver (CI) was added to maintain the same cetane number (CN) of the fuel blends as that of the baseline fuel.

A constant volume combustion simulation has been used to compute the ignition delays of pure fuels and binary fuel mixtures in air. Minima in the ignition delays were predicted by a comprehensive chemical kinetic mechanism for binary fuel mixtures with methane. A model has been developed to predict the occurrence of autoignition in a spark ignited engine. Experimental pressure data from a CFR engine were used in the model to simulate the temperature-pressure history of the end gas and to determine the time when autoignition occurred. Comprehensive chemical kinetic mechanisms were used to predict the reactions in the end gas. Methanol, methane, ethane, ethylene, propane and n-butane were used as fuels. The initial temperatures in the model were adjusted to give agreement between predicted and observed autoignition. Engine data for methane-ethane mixtures indicated a problem with the kinetic mechanism.

A detailed thermodynamic analysis was performed to demonstrate the fundamental efficiency advantage of an opposed-piston two-stroke engine over a standard four-stroke engine. Three engine configurations were considered: a baseline six-cylinder four-stroke engine, a hypothetical three-cylinder opposed-piston four-stroke engine, and a three-cylinder opposed-piston two-stroke engine. The bore and stroke per piston were held constant for all engine configurations to minimize any potential differences in friction. The closed-cycle performance of the engine configurations were compared using a custom analysis tool that allowed the sources of thermal efficiency differences to be identified and quantified.

Laser Doppler velocimetry has been used to measure velocity and turbulence intensity profiles in the wall boundary layer of a spark-ignited homogeneous-charge research engine. By using a toroidal contoured engine head it was possible to bring the laser probe volume to within 60 μm of the wall. Two different levels of engine swirl were used to vary the flow Reynolds number. For the high swirl case under motored operation the boundary layer thickness was less than 200 μm, and the turbulence intensity increased as the wall was approached. With low swirl the 700-1000 μm thick boundary layer had a velocity profile that was nearly laminar in shape, and there was no increase in turbulence intensity near the wall. When the engine was fired the boundary layer thickness increased for both levels of swirl.

A zero-dimension model of spray development and particulate emissions for direct-injection combustion was developed. The model describes the major characteristics of the injection plume including: spray angle, liquid penetration, lift-off length, and temperatures of regions within the spray. The model also predicts particulate mass output over a span of combustion cycles, as well as a particulate mass-history over a single combustion event. The model was developed by applying established conceptual models for direct injection combustion to numerical relations, to develop a mathematical description of events. The model was developed in a Matlab Simulink environment to promote modularity and ease of use.